- 您现在的位置：买卖IC网 > Sheet目录987 > LD4T06P0 (Red Lion Controls)TIMER 6 DIGIT 4.0" 120VAC RED
4.0 R EVIEWING THE F RONT P ANEL K EYS AND D ISPLAY
KEY
PAR
SEL ?
RST ?
DISPLAY MODE OPERATION
Access Programming Mode
Select display (Timer or Cycle Counter)
Reset value(s) per front panel reset setting
PROGRAMMING MODE OPERATION
Store selected parameter and index to next parameter
Advance through selection list/select digit position in
parameter value
Increment selected digit position of parameter value
OPERATING MODE DISPLAY DESIGNATORS
“ ? ” - To the left of the display is the Cycle Counter value.
“ ? ? ” - Decimal point to the far right of the display can be programmed to flash
“
?
” - Between digits 5 and 6 indicates the setpoint status.
when the timer is running, to provide a “Timer Run” indicator.
If display scroll is enabled, the display will toggle automatically every four seconds between the Timer and Cycle Counter values.
5.0 P ROGRAMMING
THE
M ETER
DISPLAY
MODE
PAR
OVERVIEW
PROGRAMMING MENU
Display and Front
Setpoint
Serial
Timer Input
Parameters
Cycle Counter
Parameters
Panel Key
Parameters
Output
Parameters
Setup
Parameters
SEL
PAR
PAR
PAR
PAR
PAR
PROGRAMMING MODE ENTRY (PAR KEY)
It is recommended all programming changes be made off line, or before
installation. The meter normally operates in the Display Mode. No parameters
can be programmed in this mode. The Programming Mode is entered by
pressing the PAR key. If it is not accessible, then it is locked by either a security
code or a hardware lock (See Module 3).
MODULE ENTRY (SEL ? & PAR KEYS)
The Programming Menu is organized into five modules. These modules group
together parameters that are related in function. The display will alternate between
??? and the present module. The SEL ? key is used to select the desired module.
PROGRAMMING MODE EXIT (PAR KEY)
The Programming Mode is exited by pressing the PAR key with ?????? ?
displayed. This will commit any stored parameter changes to memory and return
the meter to the Display Mode. (If power loss occurs before returning to the
Display Mode, verify recent parameter changes.)
PROGRAMMING TIPS
It is recommended to start with Module 1 and proceed through each module in
sequence. When programming is complete, it is recommended to record the
parameter programming and lock out parameter programming with the user input
or programming security code.
The displayed module is entered by pressing the PAR key.
FACTORY SETTINGS
???? ?? ?
MODULE MENU (PAR KEY)
Each module has a separate module menu (which is shown at the start of each
module discussion). The PAR key is pressed to advance to a particular parameter
to be changed, without changing the programming of preceding parameters.
After completing a module, the display will return to ???? ?? . Programming
may continue by accessing additional modules.
SELECTION / VALUE ENTRY
For each parameter, the display alternates between the present parameter and
the selections/value for that parameter. The SEL ? and RST ? keys are used to
move through the selections/values for that parameter. Pressing the PAR key,
stores and activates the displayed selection/value. This also advances the meter
to the next parameter.
For numeric values, the value is displayed with one digit flashing (initially the
right most digit). Pressing the RST ? key increments the digit by one or the user
can hold the RST ? key and the digit will automatically scroll. The SEL ? key
will select the next digit to the left. Pressing the PAR key will enter the value and
move to the next parameter.
6
Factory Settings may be completely restored in Module 3. This is useful when
encountering programming problems.
ALTERNATING SELECTION DISPLAY
In the explanation of the modules, the following dual display with arrows will
appear. This is used to illustrate the display alternating between the parameter
on top and the parameter ’s Factory Setting on the bottom. In most cases,
selections and values for the parameter will be listed on the right.
Indicates Program Mode Alternating Display
Parameter
? ????? Selection/Value
Factory Settings are shown.
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
LFSTBEB7361
BOARD DEV ACCELEROMETER MMA7361L
LFSTBEB7455
BOARD DEV ACCELEROMETER MMA7455L
LFSTBEB8450
BOARD DEV ACCELEROMETER MMA8450
LFSTBEB845X
EVAL BOARD FOR MMA845XQ
LH1518AT
RELAY SSR SPST 250V 300MA 6DIP
LI12-1A79
RELAY REED SPST 1A 12V
LK1AF-24V
RELAY GEN PURPOSE SPST 5A 24V
LKG1AF-24V-16-1
RELAY GEN PURPOSE SPST 16A 24V
相关代理商/技术参数
LD50
制造商:General Tools 功能描述:Deluxe Lightning Detector 制造商:General Tools 功能描述:DETECTOR LIGHTNING
LD-50
制造商:API TECHNOLOGIES 功能描述: 制造商:API Technologies Corp 功能描述:
LD5000
制造商:WTE 制造商全称:Won-Top Electronics 功能描述:50A 10mm LUCAS TYPE PRESS-FIT DIODE
LD5001
制造商:WTE 制造商全称:Won-Top Electronics 功能描述:50A 10mm LUCAS TYPE PRESS-FIT DIODE
LD5002
制造商:WTE 制造商全称:Won-Top Electronics 功能描述:50A 10mm LUCAS TYPE PRESS-FIT DIODE
LD5003
制造商:WTE 制造商全称:Won-Top Electronics 功能描述:50A 10mm LUCAS TYPE PRESS-FIT DIODE
LD5004
制造商:WTE 制造商全称:Won-Top Electronics 功能描述:50A 10mm LUCAS TYPE PRESS-FIT DIODE
LD5005
制造商:WTE 制造商全称:Won-Top Electronics 功能描述:50A 10mm LUCAS TYPE PRESS-FIT DIODE